Early Access · 8% OFF Sitewide Nov 20–25 · No minimum spend

SpeTool · S05001 · Steel body

36-inch 4-Way Panel Clamp

£188.07 GBPper pack

Give wider glue-ups the support they need. Keep boards aligned while you bring the joints together.

Not sure which size? Compare the range →
Maximum panel width 36 in / 914 mm
Stock thickness ¼–3 in / 6.4–76.2 mm

For cabinet panels, wider cutting boards and small tabletops within 36 inches.

2 clamp(s) included per pack

Shipping and any applicable taxes or duties are shown at checkout.

▶ Watch the setup demonstration

Four-way pressure

Close the joints. Keep boards aligned.

Side-to-side clamping helps bring board edges together. Top-and-bottom pressure helps keep the panel aligned during glue-up.

Four arrows show side-to-side and top-and-bottom pressure on a panel glue-up.
Pressure mechanism illustration. Body material, clamp length and capacity vary by model.

Bring edges together

Side-to-side pressure helps close the joints between properly prepared boards.

Keep boards aligned

Top-and-bottom pressure helps limit boards lifting out of alignment as you tighten.

Start with prepared stock

Use straight, square edges and dry-fit first. Clamping does not replace flattening or jointing warped stock.

Watch the setup demonstration →

Measure before you choose

Choose by panel width. Plan by panel length.

The size refers to the maximum clamping width across the boards. It is not the length of the finished panel.

  1. Measure the assembled width

    Lay out the boards edge to edge. Choose a clamp with enough capacity for the full width of your glue-up.

  2. Check the stock thickness

    Confirm your boards fall within the thickness range shown here. Dry-fit the complete setup before applying glue.

  3. Support the full panel length

    Use enough clamp positions for your panel length, stock and glue requirements. A pack count is not a guarantee that it suits every project.

S05001Capacity at a glance
Side view: maximum panel width between clamping contact points and stock thickness between the bars.A measures the panel across its glued-up width, between the clamping contact points. B measures board thickness between the upper and lower bars. AB
AMaximum panel width
36 in / 914 mm
BStock thickness
¼–3 in / 6.4–76.2 mm
Capacity schematic, not to scale. A is panel width, not overall tool length. Actual hardware details vary by model.

Diagram explains measurement only; it is not to scale. Metric equivalents are rounded. Check fit before applying glue.

See the setup

From loose boards to a supported glue-up.

See how the clamp supports the boards as pressure is applied. Start with straight, properly prepared stock.

Demonstration filmed with the 24-inch S05002. The same video is shared across the series; dimensions, pack options and setup requirements depend on the model.

Support board alignment

Vertical support helps manage board movement while lateral pressure brings the glue joints together.

Prepare before the glue

A dry run lets you check capacity, board contact and clamp placement while adjustments are easy.

Build on good preparation

Clamping does not replace jointed edges and flat stock. Check alignment as you tighten, without forcing the mechanism.

One series. Four capacities.

Match the clamp to the work you build.

Start with the widest panel you plan to glue. Then check stock thickness and the pack options available for your destination.

S05003

16 inch

Maximum panel width
16 in / 406 mm
Stock thickness
¼–2¼ in / 6.4–57.2 mm
Body material
Aluminum body

For smaller cutting boards, box panels and narrow glue-ups within 16 inches.

VIEW S05003 →

S05002

24 inch

Maximum panel width
24 in / 610 mm
Stock thickness
¼–3 in / 6.4–76.2 mm
Body material
Steel body

For cutting boards, cabinet doors and everyday panels within 24 inches.

VIEW S05002 →

S05001 · Viewing

36 inch

Maximum panel width
36 in / 914 mm
Stock thickness
¼–3 in / 6.4–76.2 mm
Body material
Steel body

For cabinet panels, wider cutting boards and small tabletops within 36 inches.

Choose pack & quantity

S05004

48 inch

Maximum panel width
48 in / 1219 mm
Stock thickness
¼–3 in / 6.4–76.2 mm
Body material
Steel body

For broad tabletops and large panels within 48 inches, with suitable bench support.

No matching regional listing available.

Product links follow your selected country. Pack options, prices and availability come from each regional product. Other destinations may have a smaller selection.

Before and after your purchase

A few useful answers before glue-up.

What arrives in the box?

The pack selector above states the number of clamps included. Quantity means packs: two packs of a two-clamp option contain four clamps. Wood, glue and the workbench shown in demonstrations are not included.

Need help with a part or setup?

Keep your order number and model code handy. Send a clear photo of the complete clamp and a close-up of the affected part so the support team can identify the correct version.

Contact SpeTool →
Does the size mean panel width or panel length?

It means maximum clamping width across the assembled boards. The length of your panel determines how many clamp positions and supports you need.

S05001: 36 in / 914 mm
What stock thickness does this model accept?

Use boards within the thickness range shown below for this model. Measure the stock after milling and dry-fit the complete setup before applying glue.

S05001: ¼–3 in / 6.4–76.2 mm
How many clamps should I use?

That depends on panel length, stock stiffness, joint preparation and the adhesive instructions. Dry-fit first and check that pressure and support are adequate along the entire glue-up. Do not assume one pair is suitable for every project.

How many clamps are in a pack, and can I order one or three?

Pack options for this regional listing:

  • 1-clamp pack — Sold out. Quantity 1 = 1 clamp; quantity 2 = 2 clamps.
  • 2-clamp pack — Available. Quantity 1 = 2 clamps; quantity 2 = 4 clamps.

The 1-clamp pack is currently sold out. The available 2-clamp packs provide even numbers of clamps, so a single clamp or a total of three clamps cannot currently be ordered from this listing.

Will these clamps flatten warped boards?

They help support alignment during glue-up, but they do not replace milling or flattening. Prepare straight, flat stock and properly fitting joints before you begin.

What if a handle, bracket or foot is damaged or loose?

Stop using the affected clamp and contact support with your model, order number and photos. Do not force a bent part straight or overtighten to compensate for movement. The team will confirm the next step and part compatibility.

What if a clamp seems to be missing from my package?

Compare the contents with the pack option on your order and inspect the packaging carefully. If the count still does not match, keep the packaging and send support a photo of the contents and shipping label.

What are the shipping and return terms?

Availability and delivery options depend on your destination and the item selected. Check the current shipping and returns policies below for the applicable terms; checkout confirms the shipping charges.

What is the clamp body made from?

Body material refers to the main clamp structure, not every fastener or component. Check the model information below when comparing the series.

S05001: Steel body
  • 5 stars: 84 (88%)
  • 4 stars: 8 (8%)
  • 3 stars: 1 (1%)
  • 2 stars: 1 (1%)
  • 1 star: 1 (1%)
Some of the reviews shown are from related products the merchant grouped with this one.
D
Dan
Great tool!

What a great tool. Definitely worth the money. They are very solid and heavy duty. If you are contemplating which size to get, just get the large ones. They do everything from small glue ups to the big ones. Highly recommended!

t
timothy j.
Great product

Clamps work great!Highly recommend.

B
BBQ Bill Wyko
Worth every penny, true quality.

These are the real deal. Rock solid steel, really easy to set up, clamps my table top dead flat. Worth every penny. I will be buying more for sure.

J
John Topping
Cutting boards friend

I did my first cutting board with the new clamps and I had to do much less sanding. I am very happy with them!

M
Maxim Zhukov
Bought them planning to return them, now I want the longer size

I picked up the 16 inch pair to glue up a few cutting boards, fully expecting to use them once and send them back. That did not happen. These are staying in my shop.Out of the box everything is well manufactured. The instructions are simple and clear, and assembly took about two minutes. The bars are stiff and do not bend under pressure, and the rest of the hardware feels premium and nice to handle. Glue does not stick to them either, so cleanup is basically nothing.I used them for three boards: a cherry one with walnut and maple stripes, a walnut one, and a maple one. Normally that means three to five pipe clamps, a lot of fussing to keep the panel from bowing, and then scraping squeeze out off the pipes afterward. With these I spent maybe five minutes getting the board aligned and under pressure. They hold the panel flat and pull the joints tight at the same time, which is exactly what I wanted. Light, sturdy, and brilliantly designed.The only con is the price. They are not cheap, but this is a case where you get what you pay for, and I am already planning to buy the longer ones.Highly recommended.

C
CSCreations
Amazing clamps!

These panel clamps are the bees knees. I’ve looked at several versions over the years from different manufacturers, and finally decided to give these SpeTool clamps a try. I wish I had bought them sooner!

m
mainsstreetwoods.net
16" panel clamps

This is my first time using a clamp like this. I was checking out some other brands and saw that these had good reviews and the price was right. I've glued up 3 boards so far, and they are very easy and quick to set up! I used some painter's tape on the bottom rail and have little to no cleanup afterwards. I used a scrap piece of wood by the rear pins just to prevent any damage to the finished piece, but don't think it's really necessary. Great clamps! Can't wait to check out more SpeTool products!

J
Jonathan Mooney
A real help

I broke these clamps in on a chaotic board I was making, 7 glue ups. It really does work as well as described. So much so, I am looking to purchase 2 more in the 36" size. Very glad I bought these, looking forward to many more years of flatter glue ups. Thanks SpeTools!

A
Annette
Esay to assemble and use

I bought these for my partner who does a lot of woodworking. They were fairly simple to assemble and understand. They held glued pieces of wood for a cutting board together almost effortlessly. They seem to be sturdier than the traditional clamps we have bought in the past. We are still determining if the higher cost is worth it at this time.

M
Marvin
Strong clamping, easy and efficient to use, and great build quality.

After starting woodworking full time a few years ago I quickly became a big fan of SpeTool. It's a toolmaker that you just know will deliver exceptional quality. These panel clamps are no exception. They are solid, heavy, durable and really easy to use.I attached a lot of photos showing a build I did of a small walnut sushi serving board. The clamps worked perfectly and they are easier to use than my DIY channel strut clamps. The main advantage of this type of clamp is they provide both lateral and vertical pressure to ensure your glue ups stay both firmly bonded on the glue lines and flat across the top and bottom surface.The alternative method is to use pipe clamps for vertical pressure and calls on the top and bottom to keep the strips flat while they are being squeezed on the jointed edges. If you don't have the top/bottom bars the panel will try to bow under the clamps' pressure like a playing card would if you squeeze it by the edges. These clamps do a perfect job of preventing bowing. You still need to ensure that A) your strips are all the exact same height and B) that they are laying perfectly flat against the bars and that they are flush against each other. The panel clamps will not correct this and push the individual strips together with its own pressure. You can see in the attachment where the strips are uneven after I've tightened the screws to apply the pressure. I had to push them back flush and then I also added a top/bottom clamp to ensure they stayed put. Not a big deal but fyi.The only other caution is the expense. These are a premium type of clamp and very efficient, and therefore you'll pay a bit more than if you built your own DIY setup out of channel struts. In my opinion, they are definitely worth it. You can see in the images of the squeeze out during the glue up, which is even and consistent and in the finished photos the seams are tight and invisible. I need a couple more in the larger sizes and I'm psyched to add this to my shop.

S
Scott
Bracket bends

When you tighten down clamp it tends to bend under pressure. I like the product , I just would like the end brackets to be stronger. I bent it back with a pliers but the strength really isn't there anymore.

S
Scott Wiley
Panel Clamps Are Great

Finally started a project where I could use the 24” panel clamps. They are a game changer. Will be ordering some 36” clamps in the near future!

K
Kevin Kirkpatrick
Fantastic

These clamps work amazingly well. Very high quality heavy duty materia and came very well packedl. Fantastic results with super easy clean up. Worked like a champ gluing up some inlay strips. Reasonably priced for what you get. I'll definitely be getting a few more

t
timothy j.
Great product

Clamps work great!
Highly recommend.

t
timothy j.
Great product

Clamps work great!
Highly recommend.

S
Steve Hayes
Great product, works

Great product, works flawless!

D
Dennis Stewart
These are so much better than anything you find

These are so much better than anything you find at rockler or harbor freight

K
Keith Kevin
Really made cutting board glue up a breeze

Really made cutting board glue up a breeze.

J
Jack Tackett
Great tool

Great tool. Makes gluing and sanding so much easier. High quality and easy to assemble. Would recommend.

R
Robert

Revolutionary concept that replaces 6-8 clamps when making cutting boards.

J
Jeffrey Riggleman
Very well built, easy to assemble

Very well built, easy to assemble. Looks like it’s made to las.

B
Bill Roberts
Shipping was prompt and well packed

Shipping was prompt and well packed. The quality is excellent.